printer_data/config/Bed_Mesh.cfg

@@ -2,7 +2,7 @@
 
 
 speed: 200
-horizontal_move_z: 10
+horizontal_move_z: 5
 mesh_min: 50, 50
 mesh_max: 300, 300
 probe_count: 5, 5

printer_data/config/print_handling.cfg

@@ -58,7 +58,7 @@ gcode:
 
   # Heating nozzle to 150 degrees. This helps with getting a correct Z-home
   SET_DISPLAY_TEXT MSG="Hotend: 150c"          # Displays info
-  #M109 S150                                    # Heats the nozzle to 150c
+  M109 S150                                    # Heats the nozzle to 150c
   CLEAN_NOZZLE
   SET_DISPLAY_TEXT MSG="Clean Boi"
 

printer_data/config/printer.cfg

@@ -168,7 +168,7 @@ endstop_pin: probe:z_virtual_endstop
 #position_endstop: -0.5
 ## All builds use same Max Z
 position_max: 250
-position_min: -8
+position_min: -3.5
 homing_speed: 8.0 # Leadscrews are slower than 2.4, 10 is a recommended max.
 second_homing_speed: 3
 homing_retract_dist: 3
@@ -226,9 +226,9 @@ stealthchop_threshold: 0
 #   Heater - HE0
 #   Thermistor - T0
 [extruder]
-step_pin: nhk:gpio23
+step_pin: PE2
-dir_pin: !nhk:gpio24
+dir_pin: PE3
-enable_pin: !nhk:gpio25
+enable_pin: !PD4
 ##  Update value below when you perform extruder calibration
 ##  If you ask for 100mm of filament, but in reality it is 98mm:
 ##  rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
@@ -244,16 +244,15 @@ microsteps: 32
 full_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degree
 nozzle_diameter: 0.400
 filament_diameter: 1.75
-heater_pin: nhk:gpio9 
+heater_pin: nhk:gpio9 #-----------------------------------------------------------------------------------------------------------------------------------------Heater Issue
 ## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
 ## Use "Generic 3950" for NTC 100k 3950 thermistors
-sensor_type: ATC Semitec 104NT-4-R025H42G 
+sensor_type: ATC Semitec 104NT-4-R025H42G #-----------------------------------------------------------------------------------------------------------------------------------------Thermistor Issue
 sensor_pin: nhk:gpio29
-pullup_resistor: 2200
 min_temp: 10
 max_temp: 280
 max_power: 1.0
-min_extrude_temp: 10 # change back to 170
+min_extrude_temp: 170
 max_extrude_cross_section: 5
 #control = pid
 #pid_kp = 26.213
@@ -267,11 +266,10 @@ pressure_advance_smooth_time: 0.040
 ##  E0 on MOTOR6
 ##  Make sure to update below for your relevant driver (2208 or 2209)
 [tmc2209 extruder]
-uart_pin: nhk:gpio0
+uart_pin: PE1
-#tx_pin: nhk:gpio1
 interpolate: false
 run_current: 0.5
-sense_resistor: 0.110 #previously 0.110
+sense_resistor: 0.110
 stealthchop_threshold: 0
 
 
@@ -352,7 +350,7 @@ samples_tolerance_retries: 3
 [fan]
 ##  Print Cooling Fan - FAN0
 pin: PA8 # Output pin controlling the fan. This parameter must be provided.
-max_power: 0.4 
+max_power: 0.8 
 # This should be set to 0.8 on most motherboards to give full range of control to your slicer. 
 # Anything above 80% duty cycle will be full power on this particular brushless driver.
 # To fine-tune the max_power parameter for your particular motherboard, set max_power to 1.0, go into the Klipper dashboard, and increase fan speed 1% at a time until the actual fan speed stops increasing as you increase the fan speed. Divide the fan speed at this point by 100 and enter it into the max_power parameter.
@@ -590,14 +588,11 @@ spi_software_sclk_pin: EXP2_2
 
 #--------------------------------------------------------------------
 
-#####################################################################
+[mcu rpi]
-#   Accelerometer
+serial: /tmp/klipper_host_mcu
-#####################################################################
+
 [adxl345]
-cs_pin: nhk:gpio27
+cs_pin: rpi:None
-spi_software_sclk_pin: nhk:gpio18
-spi_software_mosi_pin: nhk:gpio20
-spi_software_miso_pin: nhk:gpio19
 
 [resonance_tester]
 accel_chip: adxl345
@@ -644,7 +639,7 @@ unretract_speed: 25
 #*# pid_kd = 296.252
 #*#
 #*# [probe]
-#*# z_offset = 6.420
+#*# z_offset = -1.565
 #*#
 #*# [extruder]
 #*# control = pid