octoeverywhere.conf modified - 21/08/25 - 05:34:25

printer_data/config/moonraker.conf

@@ -107,3 +107,11 @@ path: ~/klipper-backup
 origin: https://github.com/Staubgeborener/klipper-backup.git
 managed_services: moonraker
 primary_branch: main
+
+[update_manager led_effect]
+type: git_repo
+path: ~/klipper-led_effect
+origin: https://github.com/julianschill/klipper-led_effect.git
+is_system_service: False
+
+

printer_data/config/printer.cfg

@@ -24,12 +24,17 @@
 ##  Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
 ##--------------------------------------------------------------------
 serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_41004C000A51313133353932-if00
-       #/dev/serial/by-id/usb-Klipper_stm32f446xx_41004C000A51313133353932-if00
+restart_method: command
+##--------------------------------------------------------------------
+
+[mcu nhk]
+##  Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
+##--------------------------------------------------------------------
+serial: /dev/serial/by-id/usb-Klipper_rp2040_4E363334320D3925-if00
 restart_method: command
 ##--------------------------------------------------------------------
 
 [include mainsail.cfg]
-[include nitehawk36.cfg]
 [include stealthburner_leds.cfg]
 [include case_lights.cfg]
 [include print_handling.cfg]
@@ -71,7 +76,7 @@ enable_pin: !PF14
 rotation_distance: 40
 microsteps: 32
 full_steps_per_rotation:200  #set to 400 for 0.9 degree stepper
-endstop_pin: PG6
+endstop_pin: nhk:gpio13
 position_min: 0
 ##--------------------------------------------------------------------
 
@@ -110,7 +115,7 @@ enable_pin: !PF15
 rotation_distance: 40
 microsteps: 32
 full_steps_per_rotation:200  #set to 400 for 0.9 degree stepper
-endstop_pin: PG9
+endstop_pin: PG6
 position_min: 0
 ##--------------------------------------------------------------------
 
@@ -237,11 +242,11 @@ microsteps: 32
 full_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degree
 nozzle_diameter: 0.400
 filament_diameter: 1.75
-heater_pin: PA2
+heater_pin: nhk:gpio9 #-----------------------------------------------------------------------------------------------------------------------------------------Heater Issue
 ## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
 ## Use "Generic 3950" for NTC 100k 3950 thermistors
-sensor_type: ATC Semitec 104NT-4-R025H42G
+sensor_type: ATC Semitec 104NT-4-R025H42G #-----------------------------------------------------------------------------------------------------------------------------------------Thermistor Issue
-sensor_pin: PF4
+sensor_pin: nhk:gpio29
 min_temp: 10
 max_temp: 280
 max_power: 1.0
@@ -299,7 +304,7 @@ max_temp: 130
 ## For the PROBE port. Will not work with Diode. May need pull-up resistor from signal to 24V.
 #pin: ~!PB7
 ## For the DIAG_7 port. NEEDS BAT85 DIODE! Change to !PG15 if probe is NO.
-pin: PG15
+pin: nhk:gpio10
 ## For Octopus Pro Probe port; NPN and PNP proximity switch types can be set by jumper
 #pin: ~!PC5
 
@@ -339,16 +344,55 @@ samples_tolerance_retries: 3
 
 [fan]
 ##  Print Cooling Fan - FAN0
-pin: PA8
+pin: PA8 # Output pin controlling the fan. This parameter must be provided.
-kick_start_time: 0.5
+max_power: 0.8 
-##  Depending on your fan, you may need to increase this value
+# This should be set to 0.8 on most motherboards to give full range of control to your slicer. 
-##  if your fan will not start. Can change cycle_time (increase)
+# Anything above 80% duty cycle will be full power on this particular brushless driver.
-##  if your fan is not able to slow down effectively
+# To fine-tune the max_power parameter for your particular motherboard, set max_power to 1.0, go into the Klipper dashboard, and increase fan speed 1% at a time until the actual fan speed stops increasing as you increase the fan speed. Divide the fan speed at this point by 100 and enter it into the max_power parameter.
-off_below: 0.10
+# This parameter defines the maximum power (expressed as a value from 0.0 to 1.0) that the pin may be set to. 
+# The value 1.0 allows the pin to be set fully enabled for extended periods, while a value of 0.5 would allow the pin to be enabled for no more than half the time. 
+# This setting may be used to limit the total power output (over extended periods) to the fan. 
+# If this value is less than 1.0, then fan speed requests will be scaled between zero and max_power (for example, if max_power is 0.9 and a fan speed of 80% is requested, then the fan power will be set to 72%).
+shutdown_speed: 0 
+# The desired fan speed (expressed as a value from 0.0 to 1.0) if 
+# The microcontroller software enters an error state. 
+# The default is 0.
+cycle_time: 0.010 #0.005 Example config value 
+# The amount of time (in seconds) for each PWM power cycle to the fan. 
+# It is recommended this be 10 milliseconds or greater when using software-based PWM. 
+# The default is 0.010 seconds.
+hardware_pwm: False 
+# Enable this to use hardware PWM instead of software PWM. 
+# Most fans do not work well with hardware PWM, so it is not recommended to enable this unless there is an electrical requirement to switch at very high speeds. 
+# When using hardware PWM, the actual cycle time is constrained by the implementation and may be significantly different than the requested cycle_time. 
+# The default is False.
+kick_start_time: 0.100 
+# Time (in seconds) to run the fan at full speed when either first enabling or increasing it by more than 50% (helps get the fan spinning). 
+# The default is 0.100 seconds.
+off_below: 0.1 
+# The blower will not spin with the included brushless driver when the duty cycle is below 8%. When scaled with Max_power at 0.8, the off_below parameter should be set to 0.1. 
+# To calibrate this setting, gradually lower the fan speed to determine the lowest input speed that reliably drives the fan without stalls. 
+# Set off_below to the duty cycle corresponding to this value (for example, 8% -> 0.08/Max_power -> 0.08/0.8 -> 0.1) or slightly higher. 
+# This parameter is the minimum input speed that will power the fan (expressed as a value from 0.0 to 1.0). 
+# When a speed lower than off_below is requested, the fan will instead be turned off. 
+# This setting may be used to prevent fan stalls and to ensure effective kick starts. 
+# To calibrate this setting, start with off_below set to 0.0 and the fan spinning. 
+# Gradually lower the fan speed to determine the lowest input speed that reliably drives the fan without stalls. 
+# Set off_below to the duty cycle corresponding to this value (for example, 12% -> 0.12) or slightly higher.
+#Tachometer_pin:
+# Tachometer input pin for monitoring fan speed. A pullup is generally required. 
+# This parameter is optional.
+#Tachometer_ppr: 1
+# When tachometer_pin is specified, this is the number of pulses per revolution of the tachometer signal.
+#Tachometer_poll_interval: 0.0005
+# When tachometer_pin is specified, this is the polling period of the tachometer pin, in seconds. 
+# The default is 0.0015, which is fast enough for fans below 10,000 RPM at 2 PPR. 
+# This must be smaller than 30/(tachometer_ppr*rpm), with some margin, where rpm is the 
+# maximum speed (in RPM) of the fan.
 
 [heater_fan hotend_fan]
 ##  Hotend Fan - FAN1
-pin: PE5
+pin: nhk:gpio5
 max_power: 1.0
 kick_start_time: 0.5
 heater: extruder

printer_data/config/stealthburner_leds.cfg

@@ -10,7 +10,7 @@
 # How to use all this stuff:
 #
 #     1.  Copy this .cfg file into your Klipper config directory and then add [include stealthburner_leds.cfg]
-#         to the top of your printer.cfg in order to register the LEDs and macros with Klipper.
+#         to the top of your printer.cfg in order for register the LEDs and macros with Klipper.
 #     2.  Define your LEDs by editing [neopixel sb_leds] below and entering the data pin from your control board
 #         as well as the color order.
 #
@@ -45,21 +45,21 @@
 #
 #     5.  Feel free to change colors of each macro, create new ones if you have a need to.  The macros provided below
 #         are just an example of what is possible.  If you want to try some more complex animations, you will most
-#         likely have to use WLED with Moonraker and a small micro-controller 
+#         likely have to use WLED with Moonraker and a small micro-controller (please see the LED thread for help inside
+#         of the stealthburner_beta channel on Discord).
 #
 #####################################
 #       END INSTRUCTRUCTIONS        #
 #####################################
 
-
 [neopixel sb_leds]
-pin: PB0
+pin: nhk:gpio7
 #   The pin connected to the neopixel. This parameter must be provided.
-chain_count: 3
+chain_count: 10
 #   The number of Neopixel chips that are "daisy chained" to the
 #   provided pin. The default is 1 (which indicates only a single
 #   Neopixel is connected to the pin).
-color_order: GRB
+color_order: GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRBW,  GRBW
 #   Set the pixel order required by the LED hardware. Options are GRB,
 #   RGB, GRBW, or RGBW. The default is GRB.
 initial_RED: 1.0
@@ -70,185 +70,273 @@ initial_WHITE: 0.0
 #   between 0.0 and 1.0. The WHITE option is only available on RGBW
 #   LEDs. The default for each color is 0.#
 
-# Most configuration for the macros can be done by modifying the variables in the _sb_vars macro
-# at the start of this file.
 
-##########
+##########################
-# MACROS #
+# LED Effects Animations #
-##########
+##########################
 
-# The following status macros are available (these go inside of your macros):
+##################
-#
+## logo effects ##
-#    STATUS_READY
+##################
-#    STATUS_OFF
+
-#    STATUS_BUSY
+[led_effect sb_logo_busy]
-#    STATUS_HEATING
+autostart:              false
-#    STATUS_LEVELING
+frame_rate:             24
-#    STATUS_HOMING
+leds:
-#    STATUS_CLEANING
+    neopixel:sb_leds (1-8)
-#    STATUS_MESHING
+layers:
-#    STATUS_CALIBRATING_Z
+    breathing  3 1 top (1,0,0)
-#
+
-# With additional macros for basic control:
+[led_effect sb_logo_cleaning]
-#
+autostart:              false
-#    SET_NOZZLE_LEDS_ON
+frame_rate:             24
-#    SET_LOGO_LEDS_OFF
+leds:
-#    SET_NOZZLE_LEDS_OFF
+    neopixel:sb_leds (1-8)
-#
+layers:
-# Contributed by Voron discord users wile.e, Tetsunosuke, and etherwalker
+    breathing  3 1 top (0.0, 0.02, 0.5)
+
+[led_effect sb_logo_calibrating_z]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (1-8)
+layers:
+        breathing  3 1 top (0.0, 0.0, 0.35)
+
+[led_effect sb_logo_heating]
+leds:
+    neopixel:sb_leds (1,3,7,8,6,2)
+autostart:                          false
+frame_rate:                         24
+layers:
+    comet  0.3  0 add (1, 0.18, 0)
+
+[led_effect sb_logo_cooling]
+leds:
+    neopixel:sb_leds (1,3,7,8,6,2)
+autostart:                          false
+frame_rate:                         24
+layers:
+    comet  0.3  0 add (0, 0, 1)
+
+[led_effect sb_logo_homing]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (1-8)
+layers:
+        breathing  3 1 top (0.0, 0.6, 0.2)
+
+[led_effect sb_logo_leveling]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (1-8)
+layers:
+        breathing  3 1 top (0.5, 0.1, 0.4)
+
+[led_effect sb_logo_meshing]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (1-8)
+layers:
+        breathing  3 1 top (0.2, 1.0, 0.0)
+
+[led_effect sb_logo_printing]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (1-8)
+layers:
+    gradient  0.3  1 add (0.3, 0.0, 0.0),(0.3, 0.3, 0.0),(0.3, 0.1, 0.0)
+
+[led_effect sb_logo_standby]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (1-8)
+layers:
+        breathing  3 1 top (0.01, 0.01, 0.01)
+
+[led_effect sb_logo_part_ready]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (1-8)
+layers:
+        breathing  3 1 top (0.0, 1.0, 0.0)
+
+####################
+## nozzle effects ##
+####################
+
+[led_effect sb_nozzle_heating]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (9,10)
+layers:
+        breathing  3 1 top (1.0, 0.18, 0.0, 0.0)
+
+[led_effect sb_nozzle_cooling]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (9,10)
+layers:
+        breathing  3 1 top (0.0, 0.0, 1.0, 0.1)
+
+[led_effect sb_nozzle_standby]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (9,10)
+layers:
+        breathing  3 1 top (0.6, 0.0, 0.0, 0.0)
+
+[led_effect sb_nozzle_part_ready]
+autostart:              false
+frame_rate:             24
+leds:
+    neopixel:sb_leds (9,10)
+layers:
+        breathing  3 1 top (0.6, 1.0, 0.0, 0.1)
 
 
-[gcode_macro _sb_vars]
+#####################
-# User settings for the StealthBurner status leds. You can change the status colors and led
+## all led effects ##
-# configurations for the logo and nozzle here.
+#####################
-variable_colors: {
+
-        'logo': { # Colors for logo states
+[led_effect sb_critical_error]
-            'busy': {'r': 0.4, 'g': 0.0, 'b': 0.0, 'w': 0.0},
+leds:
-            'cleaning': {'r': 0.0, 'g': 0.02, 'b': 0.5, 'w': 0.0},
+    neopixel:sb_leds
-            'calibrating_z': {'r': 0.8, 'g': 0., 'b': 0.35, 'w': 0.0},
+layers:
-            'heating': {'r': 0.3, 'g': 0.18, 'b': 0.0, 'w': 0.0},
+    strobe         1  1.5   add        (1.0,  1.0, 1.0)
-            'homing': {'r': 0.0, 'g': 0.6, 'b': 0.2, 'w': 0.0},
+    breathing      2  0     difference (0.95, 0.0, 0.0)
-            'leveling': {'r': 0.5, 'g': 0.1, 'b': 0.4, 'w': 0.0},
+    static         1  0     top        (1.0,  0.0, 0.0)
-            'meshing': {'r': 0.2, 'g': 1.0, 'b': 0.0, 'w': 0.0},
+autostart:                             false
-            'off': {'r': 0.0, 'g': 0.0, 'b': 0.0, 'w': 0.0},
+frame_rate:                            24
-            'printing': {'r': 1.0, 'g': 0.0, 'b': 0.0, 'w': 0.0},
+run_on_error:                          true
-            'standby': {'r': 0.01, 'g': 0.01, 'b': 0.01, 'w': 0.1},
-        },
-        'nozzle': { # Colors for nozzle states
-            'heating': {'r': 0.8, 'g': 0.35, 'b': 0.0, 'w':0.0},
-            'off': {'r': 0.0, 'g': 0.0, 'b': 0.0, 'w': 0.0},
-            'on': {'r': 0.8, 'g': 0.8, 'b': 0.8, 'w':1.0},
-            'standby': {'r': 0.6, 'g': 0.0, 'b': 0.0, 'w':0.0},
-        },
-        'thermal': {
-            'hot': {'r': 1.0, 'g': 0.0, 'b': 0.0, 'w': 0.0},
-            'cold': {'r': 0.3, 'g': 0.0, 'b': 0.3, 'w': 0.0}
-        }
-    }
-variable_logo_led_name:         "sb_leds" 
-# The name of the addressable LED chain that contains the logo LED(s)
-variable_logo_idx:              "1" 
-# A comma-separated list of indexes LEDs in the logo
-variable_nozzle_led_name:       "sb_leds"
-# The name of the addressable LED chain that contains the nozzle LED(s). This will
-# typically be the same LED chain as the logo.
-variable_nozzle_idx:            "2,3"
-# A comma-separated list of indexes of LEDs in the nozzle
-gcode:
-    # This section is required.  Do Not Delete.
 
 
-[gcode_macro _set_sb_leds]
+[led_effect rainbow]
-gcode:
+leds:
-    {% set red = params.RED|default(0)|float %}
+    neopixel:sb_leds
-    {% set green = params.GREEN|default(0)|float %}
+autostart:                          true
-    {% set blue = params.BLUE|default(0)|float %}
+frame_rate:                         24
-    {% set white = params.WHITE|default(0)|float %}
+layers:
-    {% set led = params.LED|string %}
+    gradient  0.3  1 add (0.3, 0.0, 0.0),(0.0, 0.3, 0.0),(0.0, 0.0, 0.3)
-    {% set idx = (params.IDX|string).split(',') %}
-    {% set transmit_last = params.TRANSMIT|default(1) %}
 
-    {% for led_index in idx %}
-        {% set transmit=transmit_last if loop.last else 0 %}
-        set_led led={led} red={red} green={green} blue={blue} white={white} index={led_index} transmit={transmit}
-    {% endfor %}
 
-[gcode_macro _set_sb_leds_by_name]
+#######################
-gcode:
+# LED Effects Statics #
-    {% set leds_name = params.LEDS %}
+#######################
-    {% set color_name = params.COLOR %}
-    {% set color = printer["gcode_macro _sb_vars"].colors[leds_name][color_name] %}
-    {% set led = printer["gcode_macro _sb_vars"][leds_name + "_led_name"] %}
-    {% set idx = printer["gcode_macro _sb_vars"][leds_name + "_idx"] %}
-    {% set transmit = params.TRANSMIT|default(1) %}
 
-    _set_sb_leds led={led} red={color.r} green={color.g} blue={color.b} white={color.w} idx="{idx}" transmit={transmit}
+[led_effect set_nozzle_leds]
+leds:
+    neopixel:sb_leds (9,10)
+   #neopixel:caselight
+autostart:                          false
+frame_rate:                         24
+layers:
+    static         0  0     top        (0.0,  0.0, 0.0, 1.0)
 
-[gcode_macro _set_logo_leds]
+[led_effect set_logo_leds]
-gcode:
+leds:
-    {% set red = params.RED|default(0)|float %}
+    neopixel:sb_leds (1,2,3,4,5,6,7,8)
-    {% set green = params.GREEN|default(0)|float %}
+   #neopixel:caselight
-    {% set blue = params.BLUE|default(0)|float %}
+autostart:                          false
-    {% set white = params.WHITE|default(0)|float %}
+frame_rate:                         24
-    {% set led = printer["gcode_macro _sb_vars"].logo_led_name %}
+layers:
-    {% set idx = printer["gcode_macro _sb_vars"].logo_idx %}
+    static         0  0     top        (1.0,  1.0, 1.0)
-    {% set transmit=params.TRANSMIT|default(1) %}
 
-    _set_sb_leds led={led} red={red} green={green} blue={blue} white={white} idx="{idx}" transmit={transmit}
+##############
-
+# The Macros #
-[gcode_macro _set_nozzle_leds]
+##############
-gcode:
-    {% set red = params.RED|default(0)|float %}
-    {% set green = params.GREEN|default(0)|float %}
-    {% set blue = params.BLUE|default(0)|float %}
-    {% set white = params.WHITE|default(0)|float %}
-    {% set led = printer["gcode_macro _sb_vars"].nozzle_led_name %}
-    {% set idx = printer["gcode_macro _sb_vars"].nozzle_idx %}
-    {% set transmit=params.TRANSMIT|default(1) %}
-
-    _set_sb_leds led={led} red={red} green={green} blue={blue} white={white} idx="{idx}" transmit={transmit}
 
 [gcode_macro set_logo_leds_off]
 gcode:
-    {% set transmit=params.TRANSMIT|default(1) %}
+    SET_LED_EFFECT EFFECT=set_logo_leds STOP=1
-    _set_logo_leds red=0 blue=0 green=0 white=0 transmit={transmit}
+
+[gcode_macro set_logo_leds_on]
+gcode:
+    SET_LED_EFFECT EFFECT=set_logo_leds
 
 [gcode_macro set_nozzle_leds_on]
 gcode:
-    {% set transmit=params.TRANSMIT|default(1) %}
+    SET_LED_EFFECT EFFECT=set_nozzle_leds
-    _set_sb_leds_by_name leds="nozzle" color="on" transmit={transmit}
 
 [gcode_macro set_nozzle_leds_off]
 gcode:
-    {% set transmit=params.TRANSMIT|default(1) %}
+    SET_LED_EFFECT EFFECT=set_nozzle_leds STOP=1
-    _set_sb_leds_by_name leds="nozzle" color="off" transmit={transmit}
 
 [gcode_macro status_off]
 gcode:
-    set_logo_leds_off transmit=0
+    STOP_LED_EFFECTS
-    set_nozzle_leds_off
 
 [gcode_macro status_ready]
 gcode:
-    _set_sb_leds_by_name leds="logo" color="standby" transmit=0
+    STOP_LED_EFFECTS
-    _set_sb_leds_by_name leds="nozzle" color="standby" transmit=1
+    SET_LED_EFFECT EFFECT=rainbow
+
+[gcode_macro status_part_ready]
+gcode:
+    STOP_LED_EFFECTS
+    SET_LED_EFFECT EFFECT=sb_nozzle_part_ready
+    SET_LED_EFFECT EFFECT=sb_logo_part_ready
 
 [gcode_macro status_busy]
 gcode:
-    _set_sb_leds_by_name leds="logo" color="busy" transmit=0
+    STOP_LED_EFFECTS
+    SET_LED_EFFECT EFFECT=sb_logo_busy
     set_nozzle_leds_on
 
 [gcode_macro status_heating]
 gcode:
-    _set_sb_leds_by_name leds="logo" color="heating" transmit=0
+    STOP_LED_EFFECTS
-    _set_sb_leds_by_name leds="nozzle" color="heating" transmit=1
+    SET_LED_EFFECT EFFECT=sb_logo_heating
+    SET_LED_EFFECT EFFECT=sb_nozzle_heating
+
+[gcode_macro status_cooling]
+gcode:
+    STOP_LED_EFFECTS
+    SET_LED_EFFECT EFFECT=sb_logo_cooling
+    SET_LED_EFFECT EFFECT=sb_nozzle_cooling
+
 
 [gcode_macro status_leveling]
 gcode:
-    _set_sb_leds_by_name leds="logo" color="leveling" transmit=0
+    STOP_LED_EFFECTS
+    SET_LED_EFFECT EFFECT=sb_logo_leveling
     set_nozzle_leds_on
 
 [gcode_macro status_homing]
 gcode:
-    _set_sb_leds_by_name leds="logo" color="homing" transmit=0
+    STOP_LED_EFFECTS
+    SET_LED_EFFECT EFFECT=sb_logo_homing
     set_nozzle_leds_on
 
 [gcode_macro status_cleaning]
 gcode:
-    _set_sb_leds_by_name leds="logo" color="cleaning" transmit=0
+    STOP_LED_EFFECTS
+    SET_LED_EFFECT EFFECT=sb_logo_cleaning
     set_nozzle_leds_on
 
 [gcode_macro status_meshing]
 gcode:
-    _set_sb_leds_by_name leds="logo" color="meshing" transmit=0
+    STOP_LED_EFFECTS
+    SET_LED_EFFECT EFFECT=sb_logo_meshing
     set_nozzle_leds_on
 
 [gcode_macro status_calibrating_z]
 gcode:
-    _set_sb_leds_by_name leds="logo" color="calibrating_z" transmit=0
+    STOP_LED_EFFECTS
+    SET_LED_EFFECT EFFECT=sb_logo_calibrating_z
     set_nozzle_leds_on
 
 [gcode_macro status_printing]
 gcode:
-    _set_sb_leds_by_name leds="logo" color="printing" transmit=0
+    STOP_LED_EFFECTS
+    SET_LED_EFFECT EFFECT=sb_logo_printing
     set_nozzle_leds_on